
Soot, odor, and residue removed down to the studs
Smoke Remediation in PACIFIC PALISADES, California
Smoke Remediation in PACIFIC PALISADES, California starts with finding every pocket of soot your nose already knows about. We run thermal imaging, HEPA scrubbers, and hydroxyl generators through homes from the Alphabet Streets to Marquez Knolls, then seal the surfaces so the smell stays gone. If a kitchen fire or attic burn left residue behind, call (833) 929-6186 and we will scope it the same day.
What's included
What Our Smoke Remediation Service Covers
The scope below is what a standard smoke remediation job includes. Structural rebuild, contents packing, and long-term storage are separate line items, and we tell you which is which at the scope visit so nothing shows up as a surprise on the invoice.
Thermal Imaging Inspection
A thermal imaging camera and moisture meter walk-through of every affected room, plus the attic and HVAC chase. We photograph what we find and share the images with you before work starts.
HEPA Vacuuming and Soot Sponging
Dry soot removal from ceilings, walls, framing, and hard surfaces using HEPA vacuums and soot sponges. This happens before any wet cleaning so residue does not get smeared into porous material.
Cavity Cleaning and Insulation Removal
Where smoke traveled behind drywall or into attic rafter bays, we cut out saturated insulation and bag it. A drywall saw and a careful hand keep the cut line tight so the repair patch is small.
Thermal Fogging and Air Treatment
A fogger pushes thermal fogging solution into cavities the vacuum cannot reach, then hydroxyl generators or an ozone generator run for 24 to 72 hours. We verify air quality before pulling equipment.
Surface Sealing
An encapsulant coat on framing, subfloor, and any surface that held residue. This locks in trace particles and prevents odor from reappearing when humidity rises, which matters in a coastal climate.
Final Walkthrough and Documentation
A room-by-room walk with you, a final air check, and a written report with photos. That report is what your insurance carrier needs if the claim is still open.
Service overview
What Smoke Remediation in PACIFIC PALISADES, California Actually Involves
Smoke Remediation in PACIFIC PALISADES, California is the controlled removal of soot, char residue, and odor-causing particles from every surface a fire touched, plus the cavities it did not. It is not wiping down walls. Smoke pushes through outlets, HVAC returns, and drywall seams, then cools and sticks to cold surfaces inside wall cavities and attic framing. We use a thermal imaging camera to map it, a HEPA vacuum and soot sponges to lift it, and an air scrubber running negative pressure so loosened particles leave the room instead of settling on your furniture.
Most calls we take in Pacific Palisades start with a kitchen grease fire or an electrical fire that got put out fast. The flames stop, the residue does not. Within 48 hours, acidic soot starts etching appliance finishes, pitting chrome, and staining paint and primer. If you search for professional smoke remediation near me PACIFIC PALISADES California, you want a crew that understands this town's housing stock: 1950s ranch homes with original attic framing, hillside builds with tight HVAC chases, and older properties where smoke residue remediation PACIFIC PALISADES is a cavity job, not a surface job.
The service timeline
Our Smoke Remediation Process, Step by Step
The process flexes to the condition, but these checkpoints keep decisions clear.
Emergency Scope
We arrive, walk the home with you, and photograph every affected surface. A thermal imaging camera and moisture meter tell us where smoke traveled and where firefighting water is still sitting. This first visit runs 45 to 90 minutes and ends with a written scope and a start date.
Contain and Filter
We set negative air machines and HEPA air scrubbers at the entry points, seal doorways with zip walls, and pull the HVAC filters so the system stops recirculating soot. This stage protects the rooms that were not damaged while we work on the ones that were.
Dry Soot Removal
Dry soot comes off before anything gets wet. We HEPA vacuum ceilings, walls, and framing, then use soot sponges on painted surfaces and a soda blaster or dry ice blaster on charred lumber. Insulation and drywall that absorbed residue get cut out with a drywall saw and bagged.
Wet Clean and Deodorize
Surfaces get a degreaser wash, then a fogger applies thermal fogging solution into cavities the vacuum could not reach. Hydroxyl generators or an ozone generator run for 24 to 72 hours depending on square footage and how long the smoke sat. We check the air before we pull the equipment.
Seal and Clear
Framing and subfloor get an encapsulant coat so any trace residue stays locked in. We reinstall HVAC filters, run a final air quality check, and walk the home with you room by room. Most jobs clear in 3 to 7 days; heavy attic fire damage takes longer.
Tools & methods
Equipment and Standards We Work To
Purpose-built equipment, used by trained technicians, so the job is done accurately the first time.
Thermal Imaging Camera
Finds the cold spots where smoke residue collected behind walls and in ceiling assemblies, so we open the right cavities instead of guessing.
HEPA Air Scrubber
Filters airborne particles down to 0.3 microns while negative air pressure keeps loosened soot from migrating into clean rooms.
Hydroxyl Generator
Neutralizes odor molecules safely in occupied-adjacent spaces. We run them 24 to 72 hours depending on square footage and how long the smoke sat.
Ozone Generator
Used only in unoccupied spaces for heavy odor loads. We seal the room, run it on a timer, and ventilate before anyone re-enters.
Soda Blaster and Dry Ice Blaster
Strips char from framing and brick without gouging the wood. Both are media blasters that leave a clean substrate for encapsulant.
Thermal Fogging Equipment
Pushes fogging solution into wall cavities, HVAC chases, and attic bays that a vacuum and sponge cannot reach.
Dri-Eaz and Phoenix Dehumidifiers
Pulls the moisture left behind by firefighting water so mold does not follow the smoke. Sized to the cubic footage of the affected area.
Use cases
When to Call for Smoke Remediation
These examples show how the service framework adapts rather than forcing every call through one repair.

Attic Wiring Fire, Alphabet Streets
Old knob-and-tube wiring arced in the attic of a 1953 ranch home. The fire was small but smoke pushed through every rafter bay and down into the second bedroom through a ceiling penetration. Insulation in three bays was saturated. → We HEPA vacuumed the full framing field, cut out 14 bays of insulation, soda blasted char from two rafters, fogged the cavity, and ran hydroxyl generators for 72 hours. Encapsulant went on before new insulation. Total job: 9 days.
Apartment Fire, Riviera
A bedroom fire in a second-floor unit affected the unit above through a shared ceiling assembly and the unit next door through a common wall. The landlord had three tenants asking whether their units were safe. → We scoped all three units, tested the shared HVAC, and documented what crossed over. Two units needed full remediation, one needed a surface clean and air treatment. All three cleared within 8 days and the landlord had a unit-by-unit report for the carrier.
Problems we solve
Smoke Problems We Solve in Pacific Palisades
Most smoke calls we take are not about the fire itself. They are about what the fire left behind, and what happens if nobody deals with it in the first week.
Smoke odor lingering after fire
We remove the source, treat cavities with thermal fogging solution, and run hydroxyl generators until the air reads clean. If odor returns within 12 months, we re-treat at no charge.
Hidden soot behind walls
A thermal imaging camera finds the cold spots where soot collected. We open the cavity, HEPA vacuum the framing, seal it with encapsulant, and patch the drywall as part of the same scope.
Smoke-damaged HVAC system
We shut the system down at the scope visit, pull the filters, and clean the accessible duct runs. In heavy cases we recommend a duct cleaning vendor and coordinate the schedule so it happens before we clear the job.
Insurance claim disputes
We build the scope in Xactimate, photograph every affected surface, and log moisture meter readings. Your adjuster gets line items in the format they already use, which moves most Pacific Palisades claims through in days instead of weeks.
Pricing process
What Smoke Remediation Costs in Pacific Palisades
$1,800 - $9,500 depending on scope
Square footage affected
A single room runs less than a whole floor. Smoke travels, so the affected area is usually larger than the room where the fire started. We measure it during the scope visit, not over the phone.
Days before treatment
Residue that sat for a week bonds harder and needs more cleaning passes. Jobs we start within 48 hours of the fire consistently cost less than jobs that waited.
Cavity and attic involvement
Opening walls and cutting out insulation adds labor and disposal. Attic fire damage is the biggest single driver of cost on residential jobs.
How much does smoke remediation cost in PACIFIC PALISADES California?
Most Pacific Palisades smoke remediation jobs run $1,800 to $9,500 in 2026, with a single-room kitchen fire at the low end and a whole-house job with attic involvement at the top. Square footage, how many days the smoke sat, and whether wall cavities need opening drive the number. We scope it in Xactimate and hand you the same document your adjuster will read.
What is the difference between smoke cleanup and smoke remediation in PACIFIC PALISADES?
Cleanup is surface work: wiping walls, vacuuming carpets, washing what you can see. Remediation goes after the source, which means opening cavities, cutting out insulation that absorbed residue, treating framing, and running air filtration until the readings clear. If the smell comes back a week after a cleanup, the job was cleanup, not remediation.
How long does smoke remediation take in PACIFIC PALISADES California?
A typical single-room job clears in 3 to 5 days. Whole-house jobs with attic fire damage or HVAC contamination run 7 to 14 days, mostly because hydroxyl or ozone treatment needs 24 to 72 hours of runtime after the cleaning is done. We give you a day-by-day schedule at the scope visit so you can plan where to stay.
Does smoke remediation remove odors in PACIFIC PALISADES California?
Yes, when the source is removed first. Ozone and hydroxyl generators neutralize odor molecules, but they cannot reach soot trapped behind drywall or inside insulation. We pull the source, treat the cavities with thermal fogging solution, then run the generators. If odor comes back within 12 months of our job, we re-treat at no charge.
Ready when you are
Book Smoke Remediation in PACIFIC PALISADES, California
Soot does not wait and neither should you. Call (833) 929-6186 and we will scope the job, hand you a written estimate, and start the same day on most calls. Licensed, insured, and warrantied for 12 months against odor return.

Talk with the local team
Request Smoke Remediation
Call (833) 929-6186 any hour of the day and a live technician will take your address and details. We give you an arrival window in that first call and dispatch a crew with board-up and extraction gear. If you prefer email, send your address and a few photos to info@firedamagerestorationpacificpalisades.com and we will respond the same day.


