
Soot, odor, and char removed by a certified crew that answers 24/7.
Fire and Smoke Damage Restoration in PACIFIC PALISADES, California
Fire and Smoke Damage Restoration in PACIFIC PALISADES, California starts with a crew on-site fast, not a voicemail. We pull soot off framing, run air scrubbers and hydroxyl generators to kill smoke odor at the source, and handle fire and smoke damage repair in PACIFIC PALISADES so your home is safe to walk back into. Whether it was a kitchen grease fire or an attic electrical fire, we scope it, document it for your carrier, and get the work done.
What's included
What Fire and Smoke Damage Restoration Includes
The core scope covers emergency board-up, soot and char removal, deodorization, structural drying, and the rebuild back to pre-loss condition. Contents cleaning, furniture refinishing, and HVAC duct cleaning are quoted as add-ons once we see the loss. You get the full scope in writing before we start, so there are no surprise line items halfway through the job.
Emergency Board-Up and Tarp-Over
Windows, doors, and roof openings secured within hours of arrival so weather and theft do not add to the loss. We photograph the exterior before touching anything, which keeps the claim record clean for your adjuster.
Soot and Char Removal
HEPA vacuuming, soot sponges on walls and ceilings, and drywall saw cut-back on charred material. Soda blasting handles tough char on structural lumber without gouging the grain, so salvageable framing stays in place.
Deodorization and Air Scrubbing
Hydroxyl generators run 24 to 72 hours, with thermal fogging for deep-set odor in framing and subfloor. Air scrubbers and negative air machines keep the rest of the house clean while the work is going on.
Structural Drying
Firefighting water soaks insulation and framing, and mold can start in 24 to 48 hours. Dri-Eaz dehumidifiers and air movers dry the structure on the same mobilization as the soot work, with moisture readings logged daily.
Rebuild and Finish Work
New drywall, insulation, primer and sealant, paint, and trim installed to code once moisture readings hit target. We pull the permits and handle the inspections so the house is signed off, not just visually finished.
Service overview
What Fire and Smoke Damage Restoration in PACIFIC PALISADES, California Involves
Fire and Smoke Damage Restoration in PACIFIC PALISADES, California is the full cleanup and rebuild process that starts after the trucks leave: soot removal, odor neutralization, structural drying, and putting the house back together. Smoke travels farther than flames. It pushes through drywall seams, settles into insulation, and coats the inside of your HVAC ducts, which is why a room that looks fine can smell like a campfire for months. Our technicians use thermal imaging cameras and moisture meters to find the hidden pockets before they turn into mold.
Most Pacific Palisades calls we run fall into a few buckets: kitchen grease fires that leave a fine oil film on every cabinet, electrical fires inside older walls, and attic fires that char framing and roofing shingles. We also handle the water damage from firefighting, because a 1,500-gallon hose load does its own damage. If you are searching for fire and smoke damage restoration near me PACIFIC PALISADES California at 2 a.m., we answer. A same day fire and smoke damage cleanup PACIFIC PALISADES California crew can usually be rolling within the hour.
The service timeline
What to Expect From Start to Finish
The process flexes to the condition, but these checkpoints keep decisions clear.
Emergency Board-Up
Within the first few hours we secure the property: board-up on broken windows and doors, tarp-over on roof damage, and a lock-up so the house is not open to weather or theft. We photograph the exterior before we touch anything so the claim record is clean.
Scope and Documentation
A lead tech walks every room with a thermal imaging camera and moisture meter, marks soot lines, and checks the HVAC system for smoke intrusion. You get the scope in writing the same day, and we send the photo set and Xactimate estimate to your adjuster.
Soot and Char Removal
We HEPA-vacuum loose soot first so it does not smear, then use soot sponges on walls and ceilings. Charred framing and drywall get cut back with a drywall saw to clean wood. Soda blasting handles tough char on structural lumber without gouging the grain.
Deodorization and Drying
Hydroxyl generators run 24 to 72 hours to break down smoke molecules, with thermal fogging for deep-set odor in framing and subfloor. Air scrubbers and negative air machines keep the rest of the house clean while we work. Dehumidifiers pull the firefighting water out of the framing.
Rebuild and Final Walk
New drywall, insulation, primer and sealant, paint, and trim go back in once moisture readings hit target. We do a final odor check with you in the room, hand over the moisture log, and walk the punch list before we pull the equipment.
Tools & methods
Tools and Methods We Use on Fire Losses
Purpose-built equipment, used by trained technicians, so the job is done accurately the first time.
Thermal Imaging Camera
Maps the actual smoke and heat path behind walls and above ceilings so we cut only the sections that need opening. Finds hidden soot pockets a visual inspection would miss.
HEPA Vacuum
Lifts loose soot off surfaces before anything is wiped, so it does not smear into paint or push deeper into fabric. The first step on every soot removal job.
Hydroxyl Generator
Neutralizes smoke odor molecules in the air and inside cavities. Safe to run occupied, which is why we prefer it over ozone for most residential jobs.
Air Scrubber and Negative Air Machine
Keeps the rest of the house clean while we work and contains smoke and dust to the affected rooms. Essential on multi-unit and apartment losses.
Soda Blaster and Dry Ice Blaster
Strips tough char off structural lumber without gouging the grain, so salvageable framing stays in place instead of being replaced.
Dri-Eaz Dehumidifier and Air Mover
Pulls firefighting water out of framing and insulation before mold can start. Moisture readings are logged daily until the structure hits target.
Soot Sponges and Degreaser
Dry sponges lift soot film off walls and ceilings. Degreaser cuts the oily residue a kitchen grease fire leaves on cabinets and hoods.
Use cases
When to Call for Fire and Smoke Damage Restoration
These examples show how the service framework adapts rather than forcing every call through one repair.

Attic Fire, Palisades Highlands
An attic fire charred framing and sheathing and pushed smoke down through ceiling penetrations into two bedrooms. Insulation was smoke-soaked and the roof deck had a 4-foot burned section. → We cut back burned lumber, replaced sheathing and shingles, deodorized the attic cavity, and cleaned both bedrooms before new insulation went in. Structural repairs passed inspection in 3 weeks.
Electrical Fire, Rustic Canyon
An electrical fire started inside a bedroom wall in a 1950s home with original plaster. The visible char was small, but the smell had spread through the hallway and closet. → Thermal imaging traced the burn path about 6 feet along the framing. We removed damaged wiring and charred lumber, cleaned adjacent rooms, and patched the plaster to match. The room was back in service in 10 days.
Problems we solve
Problems We Solve After a Fire
The fire is out, but the loss keeps growing if soot, odor, and water are not handled in the right order. These are the problems we see most often on Pacific Palisades fire jobs and how we shut them down.
Smoke odor lingering weeks after the fire
We run hydroxyl generators for 24 to 72 hours and thermal fog the cavities where smoke has settled. HVAC filters and duct runs get cleaned so the system does not re-odor the house. We do a room-by-room smell check with you before pulling equipment.
Hidden soot behind walls and above ceilings
A thermal imaging camera and moisture meter map the actual smoke path before we cut. We open only the wall sections that need it, HEPA-vacuum the cavity, and treat the framing before closing it back up.
Mold after fire and water damage
We set dehumidifiers and air movers on the same day as soot removal, log moisture readings daily, and do not close walls until readings hit target. Work follows ANSI/IICRC S500 and S520 standards.
Insurance claim disputes over scope
We photograph every affected room, log moisture readings, and build the scope in Xactimate so line items match what your adjuster expects. We will walk your carrier through the scope with you if a line item gets questioned.
Pricing process
What Fire and Smoke Damage Restoration Costs
$3,500 - $12,000 for most residential jobs; $40,000+ for whole-house losses with rebuild
Square footage affected
Soot and odor travel. A 200-square-foot kitchen fire can affect 1,200 square feet of living space once smoke pushes through the HVAC system. More affected area means more cleaning, more equipment, and more time.
Whether walls have to be opened
Hidden soot behind walls means cut-back and patching. Opening a wall adds drywall, insulation, primer, and paint to the scope, but leaving soot in place risks corrosion and a second remediation later.
Structural repair scope
Charred framing, sheathing, and roof decking are carpentry and permit work. The more structural lumber that has to be replaced, the higher the bill, and permit timelines can add weeks.
How much does fire and smoke damage restoration cost in PACIFIC PALISADES, California?
Most residential jobs run $3,500 to $12,000, with whole-house losses and rebuilds climbing past $40,000. A single-room kitchen fire with soot and odor typically lands in the $4,000 to $8,000 range. The big cost drivers are square footage affected, whether walls have to be opened, and how much structural repair after fire is needed. We scope it in writing before any work starts so you are not guessing.
What is the difference between fire damage and smoke damage in PACIFIC PALISADES?
Fire damage is what the flames touched: charred framing, melted fixtures, burned drywall. Smoke damage is the residue that travels: soot film on walls, acidic residue inside cabinets, and odor molecules pushed into insulation and ductwork. Smoke damage often reaches rooms the fire never entered. That is why we treat them as two separate cleanup problems, with soot sponges and HEPA vacuums for the residue and hydroxyl generators for the odor.
How long does fire and smoke damage restoration take in PACIFIC PALISADES, California?
A single-room fire with moderate soot usually takes 5 to 10 days from board-up to final walk. Whole-house losses with structural repair run 4 to 12 weeks depending on permit timelines and material availability. Deodorization alone runs 24 to 72 hours with hydroxyl generators. We give you a day-by-day schedule at the scope meeting and update it if anything shifts.
Does insurance cover fire and smoke damage restoration in PACIFIC PALISADES, California?
Yes, most homeowner policies cover fire and smoke damage restoration, including soot removal, deodorization, and the rebuild, up to your dwelling coverage limit. We document the loss in Xactimate and send the photo set and moisture logs straight to your adjuster. If your carrier disputes a line item, we will walk them through the scope with you. You are responsible for your deductible, and we will tell you upfront what that means for your out-of-pocket.
Ready when you are
Call for Fire and Smoke Damage Restoration in PACIFIC PALISADES, California
We answer the phone 24/7, dispatch a crew the same day, and scope the loss in writing before any work starts. Licensed, bonded, and IICRC-certified, with documentation your adjuster will recognize. Call (833) 929-6186 now and we will tell you what happens next.

Talk with the local team
Request Fire and Smoke Damage Restoration
Call (833) 929-6186 any hour of the day and a live technician will take your address and details. We give you an arrival window in that first call and dispatch a crew with board-up and extraction gear. If you prefer email, send your address and a few photos to info@firedamagerestorationpacificpalisades.com and we will respond the same day.



