Attic Fire Restoration

Soot, smoke and charred framing handled by licensed crews

Attic Fire Restoration in PACIFIC PALISADES, California

Attic Fire Restoration in PACIFIC PALISADES, California starts with a thermal scan, not a guess. Attic fires hide in insulation and framing, so we map every hot spot, pull the wet cellulose, and treat smoke before it settles into living space. If you need attic fire damage repair in PACIFIC PALISADES after an electrical or chimney fire, call (833) 929-6186 and we will be on site the same day.

Live phone supportUpfront optionsBacked workmanship
Call firstLive triage can help before arrival
Safety before speedRisks assessed before work begins
Diagnose the causeWe trace the source, not just the symptom
Approve the workScope and price explained upfront

What's included

What Our Attic Fire Restoration Includes

Every attic fire job starts with a written scope, and that scope covers the work below. If your loss needs something outside it, like full roof replacement or HVAC replacement, we tell you before demolition starts and price it separately so there are no surprises on the invoice.

01

Thermal Scan and Scope

A thermal imaging camera and moisture meter map every hot spot and wet pocket in the attic. We mark the rafters, photograph the findings and write the scope from that map, which takes 60 to 90 minutes on a standard attic.

02

Soot and Char Removal

Technicians hand-scrub with soot sponges, then soda blast or dry ice blast charred framing back to bare wood. HEPA vacuums and negative air machines keep soot out of the living space while the work is underway.

03

Odor Control and Sealing

Hydroxyl generators run 24 to 72 hours, followed by thermal fogging and an encapsulant coat on the rafters. That combination is what removes smoke odor from porous wood instead of masking it until the next hot day.

04

Insulation and Framing Repair

We pull contaminated insulation, sister or replace charred members to code, and reinstall insulation to the correct R-value for this climate. Attic fire insulation and framing repair PACIFIC PALISADES California work is documented for your carrier and for resale.

05

HVAC and Filter Cleaning

Smoke pulls through the return plenum and coats the filter bank. We clean the accessible ductwork, replace HVAC filters and seal the plenum so the system stops redistributing attic soot into bedrooms and hallways.

06

Final Walkthrough and Report

You walk the attic with the crew lead before containment comes down. We hand over a photo report, the Xactimate scope and a workmanship warranty so you have a record of what was done and what to watch for.

Service overview

What Attic Fire Restoration in PACIFIC PALISADES, California Involves

Attic Fire Restoration in PACIFIC PALISADES, California is the trade of removing fire, soot and smoke damage from the space above your ceiling, then rebuilding it to code. That means pulling charred insulation, soda blasting or dry ice blasting scorched rafters, sealing odor into the wood with an encapsulant, and replacing what cannot be saved. Attics are the hardest part of a house to ventilate, so smoke lingers there long after the visible fire is out.

Most local attic fires start small and stay hidden: a failed junction box, a chimney chase that overheated, a recessed light buried under blown-in insulation. By the time you smell it, soot has already coated the roof deck. That is why we treat attic fire cleanup and restoration PACIFIC PALISADES jobs as a full envelope problem, not a spot fix. If you are searching for attic fire restoration near me PACIFIC PALISADES California at 2 a.m., we answer the phone.

Stop Hidden Soot SpreadSoot behind drywall and in HVAC returns keeps circulating every time the system runs. We pull the filter bank, scrub the plenum and seal cavities so attic fire smoke and fire damage repair PACIFIC PALISADES work actually holds instead of coming back next season.
Save Framing Where PossibleCharred lumber does not always mean a new roof. We probe with a moisture meter and a thermal imaging camera, then sister or replace only the members that lost section. On a typical 1,200 sq ft attic that saves thousands versus a full tear-off.
Kill Odor at the SourceCharcoal absorbers alone will not fix a smoke smell that has soaked into rafters. We pair hydroxyl generators with thermal fogging solution and an encapsulant coat, which is the difference between a house that smells clean in 48 hours and one that still smells like a campfire in July.
Fire Damage Restoration near me in PACIFIC PALISADES, California
How we workWe verify the cause, compare realistic options, and confirm the repair before we leave.

The service timeline

How Our Attic Fire Restoration Process Runs

The process flexes to the condition, but these checkpoints keep decisions clear.

01

Emergency Board-Up

We tarp the roof, board any open vent or gable, and stop water intrusion within the first few hours. If the fire department cut a vent hole, we close it the same day so fog and marine air do not soak the attic. This stage usually takes 2 to 4 hours.

Stage 1
02

Thermal Mapping

A thermal imaging camera and moisture meter tell us where heat traveled and where firefighting water pooled. We mark every hot spot on the rafters and decking, then write the scope from that map. Expect 60 to 90 minutes for a standard attic.

Stage 2
03

Containment and Soot Removal

Negative air machines and HEPA vacuums keep soot from migrating into bedrooms. Technicians hand-scrub with soot sponges, then soda blast or dry ice blast charred framing down to bare wood. A 1,000 sq ft attic typically takes 2 to 3 days.

Stage 3
04

Odor and Air Treatment

We run air scrubbers and hydroxyl generators for 24 to 72 hours, then thermal fog the cavities with a solution matched to the fuel that burned. Protein smoke from a kitchen fire needs a different chemistry than electrical smoke, and we adjust.

Stage 4
05

Rebuild and Final Walk

New insulation, drywall, primer and paint go back to code, and we reinstall venting and HVAC filters. You walk the attic with the crew lead before we sign off. Most rebuilds finish 5 to 10 business days after mitigation ends.

Stage 5

Tools & methods

Tools and Methods We Use in Attics

Purpose-built equipment, used by trained technicians, so the job is done accurately the first time.

01

Thermal Imaging Camera

Finds hot spots and hidden soot pockets behind knee walls and under insulation before demolition starts. It is the first tool on site on every attic job.

02

Negative Air Machine and Air Scrubber

Creates containment pressure so soot and spores stay in the work zone instead of drifting into bedrooms through can lights and returns.

03

Soda Blaster and Dry Ice Blaster

Removes char from rafters and decking without gouging the wood, which preserves framing that would otherwise be replaced.

04

Hydroxyl Generator and Ozone Generator

Neutralizes smoke odor in the attic cavity. Hydroxyl units run in occupied homes; ozone is used only in sealed, unoccupied spaces.

05

Thermal Fogger

Drives thermal fogging solution into rafter pores and wall cavities where smoke has soaked in, reaching places a sponge cannot.

06

Moisture Meter and Dehumidifier

Tracks water from firefighting and dries the structure to ANSI/IICRC S500 standards before insulation and drywall go back.

07

HEPA Vacuum and Soot Sponges

Captures fine soot particles and scrubs surfaces without smearing, which is the first pass before any blasting or sealing.

Use cases

When to Call for Attic Fire Restoration

These examples show how the service framework adapts rather than forcing every call through one repair.

Attic Fire Restoration
Alphabet Streets Junction Box FireA failed junction box scorched two ceiling joists and coated 400 sq ft of attic insulation with soot. The homeowner had been told the roof needed replacing and the attic smelled of burnt plastic every time the heat ran. → We sistered the two joists, removed and replaced the insulation, soda blasted the rafters and ran hydroxyl generators for 48 hours. The roof stayed intact, the smell cleared, and the job closed at $8,900 instead of a $24,000 replacement.

Riviera Chimney Chase Fire

A chimney chase fire sent smoke through a 1,800 sq ft attic and down into the living room through can lights. Soot coated the rafters, and firefighting water soaked the ceiling drywall in two rooms. → Crews tarped the chase, dried the ceiling assembly to ANSI/IICRC S500 standards, blasted and sealed the rafters, and cleaned the can-light cavities. The family moved back in 12 days, and the follow-up scan showed no remaining hot spots.

Marquez Knolls Recessed Light Scorch

A recessed light overheated under blown-in insulation and scorched a joist bay. The tenant reported a burnt smell that returned whenever the furnace ran, but there was no visible damage from below. → A thermal scan found the scorched joist and smoke-coated insulation. We removed the insulation, cleaned the plenum, replaced the filters and sealed the bay. The unit passed a follow-up scan and re-rented in five weeks.

Problems we solve

Attic Fire Problems We Solve in Pacific Palisades

Attic fires create a specific set of problems that general contractors often miss. These are the ones we see most often on local jobs, and how we handle each.

ISSUE

Smoke odor that returns when the heat runs

We clean the plenum, replace filters and thermal fog the cavities, then seal the rafters with an encapsulant. That stops the source instead of masking it, and the smell stays gone through the next heating season.

SYMPTOM

Hidden soot behind knee walls and drywall

Our thermal scan and drywall saw access let us find those pockets before rebuild. We HEPA vacuum and seal each cavity, then document it in the photo report so you know the wall is clean before it closes.

SIGN

Charred framing that looks worse than it is

We probe each member and measure the remaining section. If it is sound, we sister a new member alongside and leave the roof intact. If it is not, we say so and price the replacement honestly.

ALERT

Water damage from firefighting

We run dehumidifiers and air movers alongside the fire mitigation, using ANSI/IICRC S500 drying standards. Drying and soot removal happen in the same phase so you do not trade a fire loss for a mold claim.

Pricing process

What Attic Fire Restoration Costs

$4,500 - $28,000 depending on scope

Phase 01

Extent of charred framing

One or two sistered rafters cost far less than a ridge beam or multiple decking sheets. We probe each member and price only what actually lost section, which keeps the scope honest.

Phase 02

Smoke travel into HVAC

If smoke reached the return plenum and ductwork, cleaning and filter replacement add cost. Skipping it is cheaper today and far more expensive when the smell returns next winter.

Phase 03

Insulation replacement

Contaminated insulation has to go, and replacement is priced by square footage and R-value. A 1,200 sq ft attic typically runs a few thousand dollars for removal and reinstall.

Questions before we arrive

Frequently Asked Questions

Attic Fire Restoration
Call (833) 929-6186
How much does attic fire restoration cost in PACIFIC PALISADES California?

Most attic fire restoration jobs in PACIFIC PALISADES run $4,500 to $28,000 in 2026, with a typical single-rafter electrical fire landing near $9,000. Cost tracks three things: how much framing is charred, how far smoke traveled into the HVAC and living space, and whether the roof deck needs replacement. Insurance usually covers the bulk of it, and we price in Xactimate so the claim lines up with the work.

How do I know if I had an attic fire in PACIFIC PALISADES?

The tell is usually smell before sight: a sharp burnt-plastic odor that returns when the HVAC runs, or a faint scorch mark around a can light or chimney chase. Look for discolored insulation, blackened rafters near a junction box, or tripping breakers on one circuit. A thermal imaging scan finds hot spots you cannot see, and we run one on the same day you call.

Can attic fire damage be repaired without replacing the roof in PACIFIC PALISADES California?

Yes, in most cases. If charring is limited to a few rafters and the shingles above are intact, we sister or replace those members from inside and leave the roof alone. Full replacement is only needed when the decking lost structural section across a large area or the fire burned through the sheathing. A thermal scan and probe tell us which side of that line you are on.

How long does attic fire restoration take in PACIFIC PALISADES California?

Plan on 2 to 4 weeks for a typical attic fire, split roughly into 3 to 7 days of mitigation and 5 to 10 business days of rebuild. Odor treatment adds 24 to 72 hours of equipment run time. Larger losses with roof deck replacement or HVAC contamination stretch to 6 weeks. We give you a written schedule after the thermal scan, not before.

Ready when you are

Get Attic Fire Restoration in PACIFIC PALISADES, California

Smoke odor and charred framing get worse with every hot day. Call (833) 929-6186 and we will run a thermal scan, write a scope in Xactimate and give you a straight answer on what can be saved. Licensed, insured and answering 24/7.

Attic Fire Restoration

Talk with the local team

Request Attic Fire Restoration

Call (833) 929-6186 any hour of the day and a live technician will take your address and details. We give you an arrival window in that first call and dispatch a crew with board-up and extraction gear. If you prefer email, send your address and a few photos to info@firedamagerestorationpacificpalisades.com and we will respond the same day.

960 Monument St, Pacific Palisades, CA 90272, USA, PACIFIC PALISADES, CaliforniaMain office · technicians serve the full area

Thanks — your request is in. We will contact you shortly.

Call now